Mid Century Mercier Meca Dural Restoration – a Brief Test Ride

Mid Century Mercier Meca Dural – Autumn 2017

MId Century Mercier Meca Dural – Winter 2017

Today I ventured out for a test ride on this Mid-Century Mercier Meca Dural – a bike which had been incorrectly modified when I acquired it last fall.  I spent the winter restoring it and replacing many of the incorrect and missing components. But, I hadn’t had time in my schedule to get the bike out on the road for a test ride until now.

Vintage Rigid Chain Guard

Carradice Long Flap saddlebag – stuffed with all the possible tools need for a first test ride.

Unfortunately, I chose a bad moment to take the bike out to Sauvie Island – one of my favorite low key cycling jaunts.  It’s the weekend before Halloween, which I realized only too late upon arriving at the Sauvie Island parking lot where cyclists normally unload their bikes for a journey around the bucolic beauty of this little island treasure near Portland.  That meant hordes of cars heading to the Pumpkin Patch – a place where kids can enjoy all kinds of thrilling Halloween activities.  There are no shoulders on the flat roads of Sauvie Island, so cyclists who venture there rely upon the good will of the Island’s drivers, which is usually just fine.  Today, however, was not the right day to take an untested bike into this environment, and that realization dawned on me after just a few minutes of cycling on the Meca Dural’s duralumin frame.

Original alloy Guidonnet Levers.

The ride I cut short to avoid the stress of a steady stream of vans and SUVs passing too close provided some valuable information.  One thing I learned was that these original guidonnet aluminum alloy levers have an unusually long reach, so if you need to brake suddenly and don’t have gigantic hands, you may not stop as quickly as you would like.

C.M. long reach calipers.

The C.M. long reach brake calipers have quite a bit of flex under hard braking.  This caused the front brake to jump a bit when I attempted to stop suddenly.  That may simply mean that the brake mounting bolts need a bit more torque – so that’s an issue to sort out.

Chain guard mounting hardware.

I also discovered that the lovely vintage Rigid chain guard which I had installed using a combination of new and vintage mounting hardware needed adjustment, as the chain rubbed against the guard in the lowest gear. Fortunately, this mounting hardware makes it very easy to adjust the position of the chain guard by turning the nuts on the long connecting bolts.

Vintage Simplex Grand Tourisme rear derailleur.

The 3 speed freewheel is mated to a 46 tooth Louis Verot chainring on Stronglight 49d crank arms.  The small cogs make for high gearing, which was almost too high even on the totally flat roads of Sauvie Island.  One solution will be to locate a vintage french threaded freewheel with larger cogs.  The bell crank actuated Simplex derailleur worked perfectly and can definitely handle larger-toothed cogs. Shifting was straightforward, with no noticeable over-shifting required. Since I didn’t have the original chain, I had guessed at the chain length.

The ride quality overall was comfortable. I attribute this primarily to these wonderfully preserved vintage Mavic 650b rims and the new Panasonic tires, inflated to fairly low pressures, as well as to the flex characteristics of the duralumin frame.  This bicycle’s frame design doesn’t include an extra set of mixte stays extending to the rear drop out.  Initially, I experienced a bit of a wobbly feel at the front end, which would likely become a non-issue once a rider gets this bike underway for a few miles.

Meca Dural ornate aluminum lugs joined by internal steel expanders. Kitty is optional equipment.

After this brief ride I know what is needed to make the bike more useful and reliable.  And, I didn’t worry about the Meca Dural aluminum tubes – they performed no differently than any steel framed bike I have ridden.  The bike as pictured weighs 24 lbs – very impressive considering the full fenders, chain guard, and dynamo lighting system.  The next time I ride this bike, I hope to have a bit longer and more enjoyable ride.

4 thoughts on “Mid Century Mercier Meca Dural Restoration – a Brief Test Ride

  1. Those alloy Guidonnet levers have me making a careful sweep with my eyes, taking them all in. I’ve used their Tektro equivalents on a number of projects now and although they are decently operating levers, and have a nice shine, I can’t help but think what they’ll look, and function, like in 80 years. My guess is the Tektro’s wouldn’t survive the test of time like your alloy’s were built for.
    But, they do seem to have the ergonomic factor down so smaller hands don’t have quite the same issue as your did with lever pull. Pluses and minuses, I suppose.

    • I think these particular guidonnet levers, which I believe were made by CLB, have a much greater distance to the bar than other models which were available. I haven’t used the Tektro version, but Dia Comp has one that provides for an easy reach from the bars.

Leave a Reply to Nola WilkenCancel reply