Look Ma, No Clearance

2014-10-29 001 006

Yes, I sliced up a set of funky vintage Bluemels in order to safely get full coverage fenders on my regular commuter – a 1990’s Terry Symmetry.  At first I had mounted them intact underneath the brake bridge and fork crown – leaving me about 4 mm of clearance, and that was after I switched to narrower 28 mm tires.  I knew I was tempting the clearance gods, and sure enough, a small piece of debris got wedged in there while I was traveling very slowly (thank those gods), and that was enough to convince me that it was time to try a different solution.

Fortunately, many have heard the call of frustrated road bike riders who want full coverage fenders but who purchased their machines during the dark, racing-fad era that finally ended just a few years ago. Such bikes are typically built with inadequate clearance for fenders, and no clearance at all if you want to run wider tires.  Now, you can find conversion brackets at a number of outlets that will allow you to essentially use modified rack mounting brackets to mount fenders over the top of the rear brake bridge and on either side of the fork crown.  River City offers a set for a mere $15.

Since I already had a bunch of these brackets lying around, I decided to make use of what I had available.  I also needed to create some more of Sheldon’s “fender nuts” which involves tapping the recessed brake mounting nut (not too far down), and using a short bolt.

2014-10-29 001 007 2014-10-29 001 006

After measuring, I cut a small section out of the rear fender.  I didn’t like the look of two giant brackets, so for the seat post side of the rear fender I used a small bracket from a hardware store and modified it, which gives a cleaner look.  That took about 10 minutes.

2014-10-29 001 004 2014-10-29 001 011

For the front fender, I did not remove any material, but cut it directly in front of the fork crown mounting bracket.  That way I could get more coverage around the front wheel.  The front section is cantilevered over the tire, and it does rattle every now and then, but not excessively so.  The mount behind the fork crown was more problematic.  I needed to get the fender up higher than the original bracket provided for, so I mangled up another hardware store bracket to come up with this unattractive solution.  I’ll replace this with a simpler and prettier solution (someday, maybe, when I get around to it, probably, eventually).

2014-10-29 001 001 2014-10-29 001 009

Meanwhile, the fenders are doing their job.  My homemade mudflap is picking up the debris that would normally hit my bottom bracket, which now looks pristine, even after a rainy, muddy ride.  And the fenders themselves feel very securely mounted – I’ve had no trouble with them at all.  Even better, I was able to remount my 32 mm tires, which I much prefer to use, especially during the winter.  And, it’s nice to be able to ride around with some vintage Bluemel’s, which look great on the Terry, and add to its fun mix of new and vintage components.

2014-10-29 002 001 2014-10-29 001 008

 

Theresa’s New (Old) Raleigh

1976 Raleigh Gran Sport

1976 Raleigh Gran Sport

My partner in all things, Theresa, has been riding a Raleigh Alyeska touring bike for the last decade or so.  While it is a great bike, it is a touring bike and relatively heavy.  So, when we ride together I often feel that I am cheating by zipping around on one of my nimbler machines.  And, the Alyeska’s top tube is just a bit shorter than she prefers, so I decided to build up this Raleigh Gran Sport, which has a longer top tube, into a lighter weight iteration of its original self.

The early 60’s version of the Gran Sport was something of a sought after machine, with Sheldon Brown describing his lust for its Campagnolo components, even though at this time the frame was built with standard tubing.  This model, which I have dated to approximately 1976, is built with Reynolds 531 tubing for both the frame and fork, and it sports a Carlton logo as well.  However, some of its original components left something to be desired, such as the low end plastic Simplex derailleurs and shifters.

2014-09-14 001 009 2014-09-14 001 010 2014-09-14 001 012

I admit to a great fondness for this beautiful sky blue color scheme.  It is reminiscent of my 1976 Centurion Pro Tour.  With the white accents, I decided it was really necessary to use white cable housing.  I set up the drivetrain using Suntour components.  I had a NOS Suntour V-GT rear derailleur that I mated to a single bar end shifter.  I used a vintage Sugino crank with an SR drilled 42 tooth ring.  The freewheel is an early index version 6 speed 14/30 Shimano.  Index freewheels actually work better with friction shifters than non-index versions.

2014-09-14 001 004 2014-09-14 001 008

I wanted to keep this bike very light and simple, so there is no front derailleur or extra shifter.  To add to its elegance and feathery weight, I decided to use my treasured Campagnolo/Mavic wheelset.  This was one of the first sets I built, using smooth as butter vintage Campy hubs laced to new Mavic Open Pro 36 hole rims.  That meant a conversion to 700c, from the bike’s original 27 inch wheel diameter – not a problem at all.

2014-09-14 001 007 2014-09-14 001 006 2014-09-14 001 014

The blue color in the Mavic logo nicely accents the sky blue frame.  For the riding position, Theresa expressed a preference to be more stretched out as well as upright enough to make city riding safe and enjoyable.  I was thinking of using these big ol’ Soma bars, but I knew I would need a pretty long reach for the stem.  I found this Nitto stem with a whopping 130 mm of reach, but it had to be shipped from Japan!

Soma Oxford bars Cardiff saddle

I also ordered this very pretty Cardiff saddle, a brand which I have come to love (one is installed on my Meral), and I will be curious to see how she likes this compared to the Brooks on her current bike.  I used Mafac Racer centerpull brakes, and installed a small TA randonneur rack to mount to the front calipers.  Probably we will add a minimalist rear rack at some point, as well as some fenders.  These 35 mm Panaracer Paselas will be perfect for the kind of riding we do.  One of the very nice features on this frame is the elegant cable stop for the rear brake.

2014-09-14 001 005

I found some light blue cloth bar tape from Velox that matches the frame perfectly.  To keep with the vintage appearance I used Velo Orange’s City brake levers.  Now this nice old Raleigh has a new look and a new lease on life.  I am looking forward to Theresa’s first test ride!

2014-09-14 001 001

1980’s Peugeot 650c Conversion

 

Peugeot Canada

I came across this Canadian Peugeot on eBay. Before I converted it to a 650c city bike, it was equipped with a mix of Shimano 600 and 105 components, and even sported some brifters, which of course had failed some time ago.  Probably, the bike was garaged after this and that is why it was in pretty decent shape.  Thank you, Shimano.

Frame saver vertical dropoutsPeugeot brake bridge2014-08-09 001 007 2014-08-09 001 0102014-08-22 001 0032014-08-22 001 004

There was a little bit of rust in the bottom bracket shell, so I decided to treat the frame with Weigle’s frame saver.  It was nice to see the vertical drop-outs, and the cutouts on the lugs were a surprise.  Most of the finish work is very good, except for the sloppy work on the seat stay brake bridge.  Of course, the serial number is  meaningless, except the “Y” makes me wonder if this was a PY model.  Canadian Peugeot’s were manufactured by Pro Cycle beginning in 1978.  The company used lug construction vs. the French models which were internally brazed.   The frame and fork are Reynolds 531.  The fast back seat stays and the unicrown fork, as well as the style of the Reynolds stickers (which are in French) made me date this bike to the mid-80’s.  I’ve never seen a Peugeot in British racing green, but I really do like this color.  There are even some gold racing stripes on the left side seat stay.  So, it doesn’t look as French as it does British.  (And, I guess that’s why it’s Canadian.)

2014-08-22 001 010 2014-08-22 001 011 2014-08-22 001 009 2014-08-22 001 008 2014-08-22 001 013 2014-08-22 001 005

I salvaged the nice Shimano 105 rear derailleur by inverting the b-screw, a la Sheldon Brown.  That made it possible to use a 32 tooth cog on the rear cassette.  For this city drive train I used a 45 tooth SR ring, a Velo Orange chain guard, and a 165 mm SR Signature crank.  With this wheel size, that yields a gear inch range of 34-93 with the 12-32 7 speed cassette pictured.  That’s just about right for any kind of city riding that involves hills.  I used Tektro’s long reach brakes, which are what I use for all my 650c conversions, and 650c Terry Tellus 28 mm tires. These tires ride quite well and are virtually bullet proof.  The wheelset is comprised of 28 hole Dura Ace hubs laced to Mavic XP12 rims in a 2 cross style.  This wheelset came off of a late 90’s titanium triathlon bike. While this set may seem positively robust by today’s standards, I am a big fan of strong wheelsets with at least 3 cross lacing and 32 spokes front and rear.  However, for a small and light-weight rider, which is who I designed this bike for, this wheelset should work just fine.

Peugeot 531 City Bike Conversion

For the rest of the build, I chose an upright position using Velo-Orange’s Monmartre handlebar with reverse Dia Compe levers.  I had some matching Shimano 105 shifters, so used those to complement the rear derailleur.  They can be used in friction or index mode with this 1 x 7 drive train.

The standover height is 29 1/2 inches.  The bike weighs 21 lbs as pictured, so it will make a very nice and responsive city bike for a small rider.

For sale now.