My 1973 Jack Taylor Tourist

1973 Jack Taylor

I seem to be on a 70’s Brit-bike craze!  But it has lasted a while, as I have had this Jack Taylor Tourist Mixte for about 8 years.  At the time I purchased it from Hilary Stone, he thought it was a 1960s model.  After the bike safely made its crossing over the Atlantic, I disassembled it for cleaning and was able to read the matching serial numbers at both the rear dropout and the steerer tube more clearly, and have now dated this bike to 1973.

2015-02-13 037 2015-02-13 036 2015-02-13 027 2015-02-13 026

The build quality of this bike is classic Taylor brothers, with incredibly smooth brazing at all the joints.  It is made, of course, with Reynolds 531 double butted tubing, and features Campagnolo dropouts, hand-hammered fenders, through-the-frame dynamo wiring, and those beautiful and colorful Jack Taylor logos.  The Taylor brothers followed the practice of building their mixte frames with a single sloping standard diameter top tube fillet brazed at the seat tube with the two extra mixte stays of fairly narrow diameter.  Having ridden all kinds of mixte frames, I have to say that this method is likely not the most ideal in terms of adequate frame stiffness.  On this bike, the head tube feels somewhat independent from the rest of the bike.  Mixte frames are best, in my opinion, when built with twin lateral sloping down tubes that extend to the rear dropouts, or if a single tube is used, extending the mixte stays beyond the seat tube also helps keep the frame adequately stiff, such as this design by Peter Weigle.

Stronglight 38T drilled

Sachs Orbit hubStronglight crankset

This is one of the few bikes I have ever ridden that was geared too low for me.  It was set up with a Stronglight 99 crankset carrying a single drilled 36 tooth ring (pictured first), mated to a Sachs-Fitchel Orbit 2 speed hybrid hub with a 6 speed cassette ranging from 14 to 28 teeth.  The hybrid internal hub is meant to take the place of the front derailleur (or add to it, if you are Sheldon Brown and want 63 gears), and it provides a direct drive, and one lower gear that is about 25% lower than the direct drive.  So, with this set-up, the lowest gear was around 24 gear inches – wow!  Unfortunately, the gearing topped out at 65 gear inches, and that meant that I didn’t have much in the way of a comfortable cruising gear, much less any way to power up to speed on a sprint.  Since I didn’t want to change out the Stronglight 99 crank, I replaced the 36 tooth ring with a 38, (pictured second), and that helped a bit.  Even so, I rarely engage the lower internal hub gear, as I really don’t need it, so I ride this bike as a 6 speed, for the most part.

1972 Jack Taylor

The photo above shows its original configuration as shipped, but it is very likely that the Sachs Orbit hub set up was not part of the original build, but was added later.  I don’t think these hubs were made until the 1980’s, and the 27 inch (yes, not 700c) rims do not match, with the rear being a Weinmann and the front rim remaining unbranded and probably the original wheel built by Ken Taylor.

This is one big mixte!  The seat tube measures 54cm and the effective top tube length is a whopping 55cm.  With its large wheels and big frame, it cuts an imposing  shadow.  The bike came equipped with no-rise French-sized mustache bars shimmed into a Milremo stem.

1973 Jack Taylor Tourist

So, I changed out the bars and stem to bring them closer to me using a tall no name stem with very little reach and some Soma Mustache bars.  I also swapped out the Madison leather saddle, which was pretty worn, with the Ideale Model 75 saddle pictured above.  Unfortunately, while looking very pretty, this leather saddle, though vintage, is still hard as a rock and needs some breaking in.  Here are photos of the rest of the components:

2015-02-13 032

Suntour V-GT rear derailleur

2015-02-13 021

Mafac cantilevers, of course.

2015-02-13 011

Milremo front hub with very stylish wingnuts.

2015-02-13 029

Soubitez dynamo

jack taylor 004

Constructeur racks front and rear, mounted only to the fenders.

2015-02-13 038

Seat stay brazing, nice and simple. The paint now looks great after weeks and weeks of cleaning and polishing.

Jack-taylor-Ladies-dets2 (2)

This photo was taken before cleaning and polishing.

Jack-taylor-Ladies-dets2

Original French mustache bars. SunTour Stem mounted shifters.

2015-02-13 034

Another broken reflector

2015-02-13 016

She’s a beauty!  I commuted on this bike for a few years, but haven’t ridden it much lately, as I still have not made ergonomic peace with it.  With spring coming, I think I will dust if off and see if I can’t make this ride a bit more comfortable for me.